Epoxy Resin Clay 4 Modeling Mold Making Tooling Patching Void Fill Repair Putty

Description

MAX EMC A/B
Epoxy Molding Compound
(1 Gallon Combined Volume)
1 Half Gallon Of Part A
1 Half Gallon Of Part B
Room Temperature Curing Bulk Mold Compound (BMC)
NO STRONG ODOR AND HEALTH HAZARD OF POLYESTER RESINS
Moldable Clay-like Consistency That Can Be Rolled, Shaped and Sculpted To Shape
Sandable, Drill and Tapped, Carvable, Machined, Painted
Excellent Adhesion To Epoxy, Polyester or Vinyl Ester Fiberglass For Repairing Boat Hulls
Excellent Adhesion To Aluminum, Steel, Concrete/Ceramic, Wood and Composites
Lightweight Density, Less Than 0.95G/CC (Will Float On Water) For RC Hobby Use
14,000 PSI Compressive Strength
Excellent Water/Salt Water Resistant for Marine/Aero Applications
Very Low Shrinkage- Dimensionally Stable And Will Not Swell During Cure
Void Free Results and Excellent Detail Pick-up and Duplication
Description
MAX EMC A/B  is an epoxy-based molding and modeling resin system that offers a formable compound that cures to a hard and durable polymer.
MAX EMC holds its profile when sculpted or formed to shape.
Upon cure, MAX EMC demonstrates excellent dimensional stability, high compressive strength, sandable and paintable finish.
MAX EMC cures to a tough but sandable compound suitable for mold making, machinable parts modeling, patching holes on composites panels, wood or metal boat hulls. It is also can be used as an adhesive for lightweight applications such as RC hobby craft, capable of bonding metals, composites, fiberglass, and SMC (Sheet Molding Compound) parts.
Use And Application
Marine and Aircraft Composite Repair and Fabrication
Patching And Void Filling
Parts Prototyping Mold
SMC Patching For Fiberglass Parts
Arts and Crafts
Honeycomb Edge Closeout
Surface Smoothing Compound
Void Filling Compound
Mold Preparation
Mold Release Application -Wax And PVA Parting Film Application
Mold Release Kit (Wax And PVA Parting Film)
https://www.ebay.com/itm/222629335338
Gel Coat Application
Gel Coat Resin
MAX GPE White
https://www.ebay.com/itm/222643966152
MAX GPE Red
https://www.ebay.com/itm/311973357781
MAX GPE Blue
https://www.ebay.com/itm/311975344112
Measure Equal Parts And Blend Until Uniform
Apply Onto Prepared Tooling
Reinforce With Fiberglass Fabric And Impregnating Resin To Form A Shell
Allow To Cure For 24 Hours And Demold
Trim Of Excess Fiberglass
Completed Female Mold
Carbon Fiber Hose Shielding For Engine Bay Made Using The MAX EMC Mold
OVERSIZE MOLD MAKING WITH MAX EMC A/B
Rear Diffuser
PROPER MIXING TECHNIQUE
How To Mix Epoxy Resin For Food Contact Coating. Avoid Tacky Spots, Minimize Air Bubble When Mixing - YouTube
Video will open in a new window
Using the eBay App? Paste link into a browser window:
[isdntekvideo]
MAX EMC A/B: Available In Larger 1 Gallon Kit Size
https://www.ebay.com/itm/311949177758
PHYSICAL PROPERTIES
Density (Mixed)
0.95 grams/cc
Foam and Color
Part A – White Putty
Part B – Off White Putty
Viscosity Mixed
Thixotropic, Non-Sag Putty
Mix Ratio
Equal Parts By Weight Or By Volume
Working Time
85 Minutes @ 77°F (25ºC) (200 gm mass)
Peak Exotherm
120°F 300 gram mass
Cure Time
24 Hrs. Minimum or 2 Hrs. @ room temperature plus 120 min.@ 212°F (100°C)
MECHANICAL PROPERTIES
Hardness
90 ± 5 Shore D
Tee-Peel Strength 180°
3.2 Lbs. per inch Width
Aluminum to Aluminum
Compressive Strength
15,800 psi @ 77°F (25
°
C)
Tensile Shear Strength
2,700 psi @ 77°F (25
°
C)
2,200 psi @ -112°F (-80
°
C)
950 psi @ 212°F (100
°
C)
Elongation
1.3% Maximum Yield
Tensile Strength
5,800 psi
Service Temperature
-67°F to 250°F
*****************************************************
PLEASE CHECK OUT OTHER AVAILABLE
RESIN SYSTEMS AT OUR eBay STORE
For our complete listing, please
Visit our eBay store!
DON'T FORGET OUR EPOXY MIXING KIT
Click The Link To Add To Order
https://www.ebay.com/itm/222623932456
EVERYTHING YOU NEED TO MEASURE, MIX, DISPENSE OR APPLY
Proportioning the correct amount is equally as important to attain the intended cured properties of the resin system.
T
he container in which the epoxy and curing agent is mixed is an important consideration when mixing an epoxy resin system.
The container must withstand the tenacity of the chemical and must be free of contamination.
Most epoxy curing agent has a degree of corrosivity, as a general practice, protective gloves should be worn when handling chemicals of the same nature.
MIXING KIT CONTENTS
1 Each Digital Scale -Durable, Accurate Up To 2000.0 Grams
4 Each 32-ounce (1 Quart) Clear HDPE Plastic Mix Cups
4 Each 16-ounce (1 Pint) Clear HDPE Plastic Mix Cups
One Size Fits All Powder-Free Latex Gloves
2 Each Graduated Syringes
Wooden Stir Sticks
Foam Brush
IMPORTANT NOTICE
Your purchase constitutes the acceptance of this disclaimer. Please review before purchasing this product.
The user should thoroughly test any proposed use of this product and independently conclude the satisfactory performance in the application. Likewise, if the manner in which this product is used requires government approval or clearance, the user must obtain said approval.
The information contained herein is based on data believed to be accurate at the time of publication. Data and parameters cited have been obtained through published information, PolymerProducts and  Polymer Composites Inc. laboratories using materials under controlled conditions. Data of this type should not be used for a specification for fabrication and design. It is the user's responsibility to determine this Composites fitness for use.
There is no warranty of merchantability for fitness of use, nor any other express implied warranty. The user's exclusive remedy and the manufacturer's liability are limited to refund of the purchase price or replacement of the product within the agreed warranty period. PolymerProducts and its direct representative will not be liable for incidental or consequential damages of any kind. Determination of the suitability of any kind of information or product for the use contemplated by the user, the manner of that use and whether there is any infringement of patents is the sole liability of the user.